Anvil Foundry™ – 10.5 Gallon
The Foundry™ Brewing System is the only all-in-one with 240V/120V dual voltage that’s as easy as flipping a switch.
Navigate between 120V (1600W) for standard brewing or 240V (2800W) for faster heating and a better boil. It’s as easy as simply flipping the switch on the back of the brewing system.Designed specifically to deflect water, the Serviceable Touch Screen is now easier than ever to maintain with four screws for quick removal—unscrew, disconnect, swap, and plug it back in. It’s that simple.
High Capacity Grain Basket hosts 1.5” of side wall perforations that drastically reduce the amount of stuck mashes from happening and improving efficiency.
With our Delayed Start Timer, your brew day begins on your schedule. Set it the night before, and wake up to perfectly heated strike water, ready to go.
Get precise and consistent heating with the Linear Digital Power Control.
Ultra-low watt density triple-element heaters prevent scorching, while double-wall insulation boosts heating efficiency and maintains stable mash temperatures.
- Maynard
8 batches and counting I love that the pump is not built in. I spilled a little grain outside of the grain tube, it clogged the pump. Since the pump wasn't under the kettle, it was very easy to unclog. I've got it on 240, right now, heats and boils very quick! With some foam axe in the boil. I've had 9.5 gallons pre boil, with no boil over. I'm at 8k in altitude, so I can lose 1.5 gallons in my boil. Looking to upgrade to the 18 gallon version, when they are available again. I'll switch this one down to 110 and heat sparge water with it. I'll be able to set, keep my sparge water and temp in one kettle!
- JimmyV
9 batches and all good so farI purchased in October 2023 and have just finished my 9th batch. I debated between 18 and 10.5 unit. I've had not issues other than needing to re-tighten a few nuts and check all connections prior to each batch - especially on the dip tube / ball valve assembly. I pour a few quarts of water and check for leaks prior to completely filling prior to each batch. I have been using this on 120V even though I have access to 240V, mainly due to evaporation specs and ability to brew almost anywhere on 110V. I don't mind a little extra time for heating to save on evaporation. The dual power was a huge influence in my decision to purchase. I have one place to brew @240V, but can brew on my deck/patio weather permitting or kitchen, basement, etc. @110V. I can always mash/brew twice for a 10gal batch but prefer variety so this size is perfect for the 5-6 gal yield. At 110V, the humidity produced hasn't been an issue. I think at 240V it could be when brewing indoors. Control panel is easy to use and I have the re-circulation kit that works well, very easy to use. I have been using 10-13 lbs of grain with no issues (I use 1lb rice hulls for the larger grain batches). I follow the manual and stir the mash every 15 min. Temp readout has been very close to my handheld digital thermometer. It hasn't varied by more than a degree and with the recirc. kit running, it's spot on. I've tried both sparge and no sparge methods as outlined in the manual and have not seen any notable difference in efficiency. I pay more attention to my ph level rather than to sparge or not. I didn't buy the whirlpool arm since others have said it didn't do much and I can get the same effect with my mash paddle or large spoon. I don't think it will do much at this size of kettle. I do wish there was a screen for the dip tube as I do tend to get a bit of hops material even after whirlpool rest. Also, unlike the 18 gal unit, this only has 1 set of clips for the malt tube to drain on. I will probably add a second set for similar reasons as the 18 gal unit due to weight/drainage. Cleaning is easy and just manageable with the 10.5 size. In-doors it fits just right in my laundry room sink It looks like you can possibly remove the lid knob and replace with airlock and ferment right in the kettle. I haven't tried as it would tie up my brew kettle too long. I wish Anvil had the XP pump option when I purchased.
- ChicoAlum2009
Solid, easy to use, dual voltage, and just oh so cool!After getting solar installed on my house I told myself the next "upgrade" was going to be moving from propane to an electric setup. And after doing loads of research I decided to stick with the brand that I have grown to love and got myself a Foundry. I could not be happier with my decision. First and foremost, the Anvil Foundry 10.5 is the perfect size for 5gal batches. Second, and this is a big unexpected bonus, my brew day has actually shortened by a couple of hours from my propane days due to how simple this thing is to operate and how I now require less vessels/gadgets to brew with. Thirdly, and the main selling point at first, the dual voltage. I knew I wanted 240v because since I have a gas clothes dryer, I have an available 240v outlet in the garage. However, I can take this unit to my buddies house and brew with 120v no problem. Lastly, the foundry is so quiet! At first you never realized how loud your propane burner actually was, but after a couple of batches you quickly forget. All this, combined with my riptide pump for the easiest recirculating and whirlpooling you can imagine, my brew days have never been better! I am kind of kicking myself for not joining the "electric revolution" earlier. No more fearing that I will run out of gas mid-boil. Plus, with the solar on my home, my brew days are net zero energy usage meaning brewing was essentially "free" (and yes, I do get a kick telling my friends that the beer they are drinking was "100% brewed by the sun"). If you are looking to finally move from gas to electric, you can do no wrong in picking yourself up a Foundry!
